DC Modchip Solder Points

Dreamcast 4 Wire Modchip Install

Throughout the life of the Dreamcast there have been a number of different mod chips, the most recent being the 4 wire version, with only 4 wires to solder to quite large points it is relatively easy to install.  Whoever you bought your chip from would normally provide instructions, just in case they don’t though – read on…

Taking the DC apart is easy, the only tip I can give you is to remember which kind of screw went where.  Some people mix up the short/long silver coloured screws – the GD ROM drive is held on with 3 short screws, if you put a long one through here then you’ll damage the motherboard.  So be careful!

Here’s a typical 4 wire mod chip, make a note of the colours, the chips that I’ve used have always followed this colour coding – B Yellow, A Green, + Red, – Black, check yours and make a note of them.  Check that the pre-soldered wires are secure, re solder them if they look or feel a bit dodgy.  Don’t forget to insulate the chip.

Dreamcast Mod Chip on Circuit Board

Dreamcast Mod Chip Insulated

Once you’ve removed the power board and it’s plastic shield, the GD ROM drive, the controller ports and the final metal shielding you’ll finally reach the upper side of the motherboard which you need to solder the chip onto.

Here’s an overview of the locations for soldering the wires, remember the colour coding (in this case B Yellow, A Green, + Red, – Black).

DC Modchip Solder Points

Lets start with wire A, this wire should be soldered to leg 28 of the 44 leg chip at location IC501, the BIOS chip I think.

DC Modchip Wire A

Wire B is easier, look for the 3 legged chip at location D501, and solder as shown.

DC Modchip Wire B

Finally it’s just the Power wires to solder, very clearly marked at location CE502.

DC Modchip Power Wires

Now you need to replace the metal base/shield, if you’ve soldered your wires as shown above, then route them out of the gap near the GD ROM connector like this.  This way they will not interfere with the metal shield or get squashed.

DC Modchip Wire Route

Place the GD ROM drive back on, and stick the mod chip down as shown, that’s it – you’re finished.  You could partially re-assemble your console and test it, or just have some confidence and screw it back together and test it.

DC Modchip Finished

If you are performing this on an NTSC console which you plan to use some PAL games then you may want to consider the PAL Fix as well.

If you perform this on a PAL console then you may find that some NTSC games will run at 50Hz with black borders.  The only way to fix this is with either a boot disk (DC-X, Action Replay, Gameshark) for those games, by running the DC through a VGA box (most games will work in VGA mode, or can be forced to work) or by changing the region/video mode of your machine.  If you decide to get an NTSC console you can make life easier by fitting the PSU unit from a Dreamcast of your country to it, I have placed UK PSU’s into both American and Japanese Dreamcasts with no problems at all.

Extra Information

If you want to swap discs and put a different region game in, then you’ll need to switch you console off, and start it up with the different regions game in.  If this bothers you, it is possible to fit a RegionFree BIOS to your machine instead.

You could change the video mode and/or region of your Dreamcast.

You may buy a 4 wire modchip that is just a chip with no wires, not even mounted on a circuit board.  Here’s a couple of photos showing how to wire it up, I’ve kept the same colour coding as above to make it easier to follow.  For the 2 +5v points, I linked them up using a leg cut from an resistor and then soldered the wire to that, you could just strip a bit more of the wire and solder it to both legs.

DC Modchip No Board

DC Modchip No Board, Soldered